Pololu ACS709 Current Sensor Carrier -75 to +75A

PololuSKU: EXP-R25-039

Preis:
Sonderpreis14,20 €

Exkl. MwSt. zzgl. Versand

Lagerbestand:
Verfügbar (13 Stück), versandbereit

Hersteller-Artikelnummer: 2199
Zolltarifnummer: 85322200
Herkunftsland: US

Schneller Versand innerhalb 24h
Versand aus Deutschland
Verschlüsselte Zahlung

Beschreibung

This current sensor is a carrier board or breakout board for Allegro?s ACS709LLFTR-35BB-T Hall effect-based linear current sensor with overcurrent fault output; we therefore recommend careful reading of the ACS709 datasheet (483k pdf) before using this product. The sensor has an operating voltage of 3 ? 5.5 V and an output sensitivity of 18.5 mV/A when Vcc is 3.3 V (or 28 mV/A when Vcc is 5 V). The following list details some of the sensor?s key features:
  • Optimized accuracy for bidirectional input current from -37.5 to 37.5 A, with a linear sensing range from -75 to 75 A (see warning note below for thermal limitations).
  • Conductive path internal resistance is typically 1.1 m?, and the PCB is made with 2-oz copper, so very little power is lost in the board.
  • Integrated shield greatly reduces capacitive coupling from current conductor to die and prevents offset drift in high-side applications.
  • Use of a Hall effect sensor means the IC is able to electrically isolate the current path from the sensor?s electronics (up to 2.1 kV RMS), which allows the sensor to be inserted anywhere along the current path and to be used in applications that require electrical isolation.
  • 120 kHz bandwith that can optionally be decreased by adding a capacitor across the board pins marked ?FILT?.
  • High accuracy and reliability: typical total output error of 2% at room temperature with factory calibration, an extremely stable quiescent output voltage
  • Automotive-grade operating temperature range of -40°C to 150°C.
  • User-settable overcurrent threshold: FAULT pin output latches low when current exceeds the configured threshold for a duration that can be set through the addition of an external capacitor.
The pads are labeled on the bottom silkscreen, as shown in the picture above. The silkscreen also shows the direction that is interpreted as positive current flow via the +i arrow.

Note: The sensor?s extended -75 to 75 A range should be limited to transient currents. In our tests, we found that the IC could tolerate 50 A for 20 seconds or 37.5 A for 150 seconds before exceeding its maximum temperature rating of 150°C. Therefore, unless you are taking special steps to keep the IC cool, we recommend limiting continuous currents to under 30 A. Even with a low conductive path resistance of 1.1 m?, the board can get hot enough to burn you when the current is in the tens of amps, and the IC does not feature any kind of over-temperature protection, so thermal issues should be taken into consideration for high currents.

Dimensions:
  • Size: 0.82? x 0.9?
  • Weight: 1.7 g1
Specifications:
  • Current sense: 0.018 V/A2
  • Minimum logic voltage: 3 V
  • Maximum logic voltage: 5.5 V
  • Supply current: 11 mA
Notes:
  • 1. Without included hardware.
  • 2. When Vcc is 3.3 V. This specification is proportional to Vcc.
Documents:

Verschlüsselte Zahlung

American Express Apple Pay Google Pay Maestro Mastercard PayPal Shop Pay Union Pay Visa

Ihre Zahlungsinformationen werden sicher verarbeitet. Wir speichern keine Kreditkartendaten und haben auch keinen Zugang zu Ihren Kreditkartendaten.

Zusätzliche Informationen

Zolltarifnummer:
85322200

Herkunftsland:
US

Das hängt davon da, wo Sie sich befinden. Nach Übergabe der Bestellung an UPS beträgt die Lieferzeit in Deutschland ca. 2-3 Tage, innerhalb Europas ca. 1 Woche.

Wir versenden unsere Artikel mit unserem Versandpartner UPS.

Kundenservice

+49 (0)681 9659 0150

Kontaktieren Sie uns

info@exp-tech.de

Könnte Ihnen auch gefallen
Zuletzt angesehen