Teensy to XBee Adaptor Kit

PJRCSKU: EXP-R05-786

Preis:
Sonderpreis4,52 €

Exkl. MwSt. zzgl. Versand

Lagerbestand:
Nur noch 3 verfügbar

Hersteller-Artikelnummer: KIT_XBEE_ADAPTOR
Zolltarifnummer: 85423990
Herkunftsland: US

Schneller Versand innerhalb 24h
Versand aus Deutschland
Verschlüsselte Zahlung

Beschreibung

This kit lets you easily connect Teensy to a XBee wireless module.

Kit Contents:

  • 1: Bare Circuit Board
  • 1: MCP1825 3.3 Volt Regulator
  • 1: Capacitor, 1µF, 805 SMT Size
  • 1: Resistor, 15K (tan body)
  • 1: Resistor, 10K (blue body)
  • 2: Socket, 10 Pins, 2 mm pitch

Assembly Steps:

1: Trim board edges.

2: Solder MCP1825 and 1 µF Capacitor

Tweezers should be used to hold the each part in place while soldering the first pin. The MCP1825 tab should be soldered last. The iron may need to be left in contact for many seconds to transfer enough heat for the solder to flow.

Solder MCP1825 and 1 µF Capacitor

3: Solder 10K & 15K Resistors

The 15K resistor has a tan body, with stripes: Brown, Green, Orange, Gold.

The 10K resistor has a blue body, with stripes: Brown, Black, Black, Red, Brown.

4: Solder 2 jumpers to configure for Teensy vs Teensy++

Configured for Teensy

Configured for Teensy

Configured for Teensy++

Configured for Teensy++

5: Solder Headers or Sockets for Teensy

You will need headers and/or sockets soldered between the XBee adaptor and Teensy. When soldering headers, a breadboard can be used to hold them straight.

Solder Headers or Sockets for Teensy

6: Solder sockets to XBee

Solder sockets to XBee

Teensy 3.0 Usage

This XBee adaptor was original designed for Teensy 2.0 and Teensy++ 2.0. However, it can be used with Teensy 3.0 with the following changes:
Configure the adaptor for Teensy 2.0. That will route the signals to pins 7 and 8, which are Serial3 on Teensy 3.0.

You'll need XBee 0.4. This newest version lets you configure which serial port it uses. In your code, you'll need "Serial3.begin(9600)", and then "xbee.setSerial(Serial3)" to use that port.

Do not use the 15K resistor. Or if you've already soldered it, just cut it off the board. Those 2 resistors divide the 5V transmit signal from Teensy 2.0 to only 3 volts for the Xbee. On Teensy 3.0, the signal is already 3 volts. It's fine to leave the 10K resistor in place. You could also just solder a wire instead of the 10K resistor. Either way is fine.

If using the USBtoSerial program to test, you'll need to edit the code to use Serial3.

Verschlüsselte Zahlung

American Express Apple Pay Google Pay Maestro Mastercard PayPal Shop Pay Union Pay Visa

Ihre Zahlungsinformationen werden sicher verarbeitet. Wir speichern keine Kreditkartendaten und haben auch keinen Zugang zu Ihren Kreditkartendaten.

Zusätzliche Informationen

Zolltarifnummer:
85423990

Herkunftsland:
US

Das hängt davon da, wo Sie sich befinden. Nach Übergabe der Bestellung an UPS beträgt die Lieferzeit in Deutschland ca. 2-3 Tage, innerhalb Europas ca. 1 Woche.

Wir versenden unsere Artikel mit unserem Versandpartner UPS.

Kundenservice

+49 (0)681 9659 0150

Kontaktieren Sie uns

info@exp-tech.de

Könnte Ihnen auch gefallen
Zuletzt angesehen